Verify

Places where the manual's pages and its parts list disagree, or where the data was placed by hand. Tick an item once you have checked it on the machine; ticks stay on this device.

0 of 16 verified

Component data

Count the flashers in the machine. The solenoid table on Operations Manual p. 3-6 gives 6 flasher circuits with 14 bulbs; the parts list sums to 15 × #906, three of them on top of the backbox.
Solenoids and flashers Operations Manual p. 3-6
Check the EOS switch type on the lower and upper flippers. The parts list says SW-1A-194 (make) lower and SW-1A-193 upper; the flipper page, Operations Manual p. 2-16, lists only SW-1A-193 for base model A-15205-R, and its assembly note describes contacts that open at end of stroke, which is the opposite of a make switch. Look at the switch at rest with the coil unpowered: contacts apart means normally open (make), contacts touching means normally closed. Write down what each flipper has.
F1: Details F2: Details A6 Flippers
The fuse on solenoids 01–28 is derived from the fuse list (F105 = solenoids 01–08 and so on), not printed per coil, except the magnets 16, 23 and 24, whose 5A S.B. fuse is printed in a footnote on Operations Manual PDF page 2. Spot-check one coil per fuse against the wiring.
Fuses, LEDs and jumpers Solenoids and flashers
The manual gives two wire colours for GI strings 2, 4, 5: the GI table on Operations Manual PDF page 2 has Orange, Green and Violet, the fuse list on Operations Manual p. 1-47 has White-Violet, White-Orange and White-Green. The GI table in the app shows the GI table's colours and the fuse rows the fuse list's. Read the wire at J120-2, J121-5 and J121-6 on the power driver board and note which source is right for each string.
Fuses, LEDs and jumpers Operations Manual PDF page 2 Operations Manual p. 1-47
The magnets 16, 23 and 24 are starred in the solenoid table, and its footnote on Operations Manual PDF page 2 puts their fuse, a 5A S.B., on the underside of the playfield. The app shows that fuse for them instead of the F104 and F111 the fuse list gives by solenoid number. Find the fuse under the playfield, check its rating and note which magnets it feeds.
SOL 16: Details Operations Manual PDF page 2
The magnets' supply is stated three ways: the solenoid table on Operations Manual PDF page 2 labels their 20-9247 coil "12V", A5 puts them in the 20 V group at TP7, and A6 has the Extra Flipper Supply board A-15416 feed them 50 V through J903. With the game on, measure J903 pins 1 and 2 against pins 3 and 4, as A6 describes, and write down the reading.
SOL 16: Details A5 Power driver board A6 Flippers

Maps

Lamps L13 and L71 are placed by hand on the map, not snapped to a callout on the manual page. Compare their markers with the machine.
L13: Show on map L71: Show on map
Cousin It (44a/44b) has four markers in the original callout drawing. Confirm which two are the switch positions.
44: Show on map

Transcription

The test menu, Operations Manual p. 1-16 to 1-18, was typed from machine-read text and never read against the manual pages. Read it once against the page images.
Test menu Operations Manual p. 1-16
Spot-check the figures in the difficulty and pricing tables (Operations Manual p. 1-22 to 1-26 and 1-40); single digits in dense tables are the most likely transcription slips.
Difficulty and presets Operations Manual p. 1-22 Operations Manual p. 1-40

This machine

The backbox photos of 2026-09-24 show an anyPin NVRAM module at U8 and a black block below it that looks like the battery holder, covered or removed. Confirm that no old cells remain in or under it.
Machine setup step 7, Upgrades and upkeep A5 Power driver board
The jumper row W11–W18 next to J204 on the CPU board is visible in the photos but not readable. A European game should have W16 out and the others in; read them and write down what you find.
Operations Manual PDF page 2
The machine label on the backbox reads "20017 …" in the photos; read the full serial number and write it down.
Set A.1 24 Show Date and Time to NO: with NVRAM at U8 and no battery the clock only runs while the game is on, so the displayed time is wrong after every power-off.
Machine setup step 3, Standard adjustments

Adjustments

H-4 adjustments beyond A.2 26 (A-MODE SOUND, A-MODE MUSIC, GAMEOVER KICKOUT, SPOT GREED/BALL, FREEPLAY MESSAGE, SPOT T-H-I-N-G) come from the ROM string table. Verify number, order and options in the machine menu.
Machine setup step 5, H-4 ROM adjustments Adjustments A.1–A.5
The custom message format (2 rows × 16 characters per frame) comes from the owner's machine, not the manual. Count how many frames the menu accepts.
Machine setup step 6, Utilities after the move Adjustments A.1–A.5